Pintejin specializes in custom sheet metal fabrication service and more. Advanced china engineering team and machinery is what sets us apart from our competitors.Contact us(via [email protected]) to learn more about our capabilities and how we can serve you.

Requirements for Repair of Crash Injuries in Auto Parts Cabs

For local collisions, the cab is damaged but does not affect the deformation of the skeleton. Generally, the method of percussion can be used to correct it. When necessary, use some special tools, such as a pick hammer and a specially shaped horn. If the skeleton has been impact deformed, the skeleton correction and the shell correction should be combined and performed simultaneously. If the casing is easy to remove, it can be calibrated separately.

If the impact of the cab of the auto parts is very serious and cannot be corrected directly, it can be partially disassembled for correction.

Open the original solder joint with a hand electric drill or manual grinding wheel, and then remove the outer layer with a hacksaw or gas cutting. When the deformation range is large, the outer layer can be removed in pieces, corrected separately and then assembled together.

When calibrating and leveling, attention should be paid to the cooperation between the various components, and attention should be paid to the shrinkage and deformation of the material during welding, so as not to bring difficulties to the subsequent assembly.

When the door and cab are repaired respectively, they should be assembled and adjusted.

Assembly quality requirements: the door is installed on the cab and should rotate freely; there is no feeling of popping out after the door is closed; the matching gap between the edge of the door and the cab should be uniform; the door should be locked flexibly, and the engagement depth of the latch should meet the design requirements.

Adjustment method: first adjust the distance between the upper and lower door iron chains to the right, and the door can rotate flexibly, and then adjust and correct as follows.

First, observe whether the upper and lower gaps of the two vertical seams at the front and rear of the door are uniform. If the top seam of the door is small in the front and the rear is large, and the bottom seam is large in the front and the rear is small, it means that the door is sinking due to the bending of the sheet material at the door hinge or the fixing plate, which can be corrected.

There should be a gap of 5~6mm between the bottom seam of the door and the lower beam of the door frame, so as not to wear the lower beam of the door frame due to the sinking of the door due to deformation and wear during use. At the same time, the outer planes of the doors and cab door frames should be adjusted. The front moves inside and outside through the hinge, and the rear moves inside and outside through the lock to achieve the flush between the door and the outside of the cab. After the door position is determined, adjust the impact stopper so that the core head of the impact stopper and the impact stopper are accurately aligned, engage well, and can be opened and closed flexibly. If you find that the opening and closing are not flexible, you can add some oil to the slide of the stopper for lubrication. If the meshing width is not enough 6mm, a pad can be added under the core of the stopper. The thickness of the pad should ensure good meshing, and it will not collide with the cab frame due to the high pad.

If the upper and lower gaps of the front and rear vertical seams of the door and the cab door frame are consistent, and the gap between the top seam and the bottom seam is quite different, it is generally caused by the deformation of the cab. At this time, observe the position of the impact stopper in the core. When the core on the door is low and lower than the impact stopper, it means that the front corner of the cab is sinking and must be repaired with a special pulling tool. If the front end of the bottom gap is small and the rear end is large, it means that the rear corner of the door frame is sinking, and the correction method is opposite to the above.

In the assembly process, there are many problems that occur randomly, and the specific reasons should be found out and then the feasible method should be determined.

Automotive Sheet Metal Fabrication

Pintejin Sheet Metal shop offers a cost-effective solution for a wide range of industries with our custom metal stamping and custom sheet metal fabrication capabilities. Our stampnig operations include a variety of sheet-metal forming manufacturing processes, such as punching, blanking, embossing, bending, flanging, and coining. Our professional, experienced and well-trained engineers can execute the complex metal stamping operations with precision and accuracy.

No matter what your metal fabrication needs are, Pintejin can offer the right solution: from single sheet metal part or sub-assembly of stamped metal parts to turnkey solutions for mechanical and electrical assemblies. We have the technology, equipment and the experience to fabricate customised metal products from aluminium sheet metal fabrication, steel, zinc plated steel, stainless steel sheet metal fabrication, brass and copper. Designs that require CNC machining of surfaces or components can be accommodated. We can supply polished, galvanized, zinc coated or powder coated finishes for any sheet metal work or stamped metal components. Coupled with our accurate and reliable metal fabricating equipment, we guarantee precision and repeatability in custom sheet metal work. You’ll be taking advantage of the best sheet metal fabrication china can produce.

ABOUT US

With Pintejin automated and highly streamlined sheet metal fabrication service, you can expect a sheet metal fabrication quote within 12 hours and lead times as quickly as three days.Our rapid prototyping offering also includes a solid and reliable manufacturing capability (led by our expert team with 15+ years of experience) and technical and quality assurance, including SGS and RoHS material certifications, in-process quality reports, and First Article Inspection.

CONTACT US

EXTRA NAVIGATION

  • Automotive Sheet Metal
  • Electronic Sheet Metal
  • IPC Sheet Metal
  • LED Light Sheet Metal Parts
  • Laser Cutting China
  • Pintejin.com

Sheet Metal Fabricator
Logo